RME RPM interface (for Hammerfall DSP) - Computer Hardware
The RPM allows for the connection of 2 turntables or 2 line-sources (CD, DVD, sampler etc.) and a microphone to a desktop or laptop computer. A total of 5 independent inputs are routed to 2 stereo outputs plus a separate headphone output, which lets you monitor any of the in- and outputs at any time via TotalMix, RME's unique DSP based mixer. External devices can be connected via MIDI I/O to communicate with any adequate audio software. A Neutrik XLR/phono combo jack on the front panel gives access to a microphone preamp with the same discrete Class-A frontend found in the RME QuadMic. Its level control ranges from 10 to 60 dB to match any application and microphone. 2 low-noise turntable inputs (Cinch/RCA) with integrated RIAA frequency correction for moving magnet cartridges are located on the back panel. A simple mouse click in the settings dialog lets you change the hardware input sensitivity in three steps within a range of 6 dB. Align the output of your turntables with other equipment connected and optimize the input signal fed to the internal A/D converters. To connect CD-players, tape decks, samplers or other line sources, the phono inputs can easily be switched to "line" with another mouse click. A 6 dB pad function can be engaged to prevent overload, and to optimize gain and level balance between different sources. OUTPUTS Two individual stereo line signals can be output at the back panel's Cinch/RCA connectors. The signals present at the MAIN outputs are also available at an additional pair of balanced stereo TRS jacks, with their levels increased by 6 dB. Possible applications would be e.g. simultaneous connection of a tape deck and a professional power amp, a monitor amp and a DI box on stage, and many more. The stereo jack on the front panel can be used as an additional (third) independent stereo output, or as a headphone connector. The RPM comes with a built-in hardware mixer based on RME's TotalMix technology. Its capability to route and mix any of the inputs and outputs provides the RPM with 3 independent stereo submixes. TotalMix offers perfect monitoring and PFL functionality, removing the need for an additional external mixing desk in many cases. All inputs and outputs are internally processed by high quality AD/DA-converters operating at 110 dB signal/noise ratio. The extremely low jitter on the internal clock results in a superb 24 bit conversion from 32 up to 96 kHz. STAND ALONE OPERATION RME's exclusive Disconnect mode lets you adjust level, input selection and signal mix via your computer, and simply detach the RPM afterwards. If you do not need to record or playback audio with your computer the RPM still serves as a preset mixing preamp, a microphone preamp, headphone mixer or line-splitter with balanced signal output - whatever you need. BYPASS In case of power failure or with your computer disconnected, the phono inputs will be hard-patched to the line outputs. Even in an emergency the unit will still serve as a phono preamp and prevent a complete audio dropout APPLICATIONS Phono/CD/Mic interface. The computer only supplies the user interface and the level meters of the mixer (TotalMix). As above, with sound files playing at the same time. As above, recording the complete session to the computer. All audio is supplied by the computer. The RPM serves as mic preamp, line output and headphone amplifier. The turntables do not play audio but time code to remote control dedicated DJ-software (DigiScratch, PCDJ Scratch etc.) Scratch control via MIDI input (external MIDI controller). The MIDI output controls an external sample player (Groovebox etc.) via MIDI time code. The analog output of the player can be mixed with any other signal using the line input of the RPM and TotalMix. Allows for the connection of 2 turntables or 2 line-sources and a microphone. Requires Hammerfall DSP PCI or laptop card. Click Here for More Information about RME RPM interface (for Hammerfall DSP). RME RPM interface (for Hammerfall DSP) Computer Hardware - RME - Delivery for RME RPM interface (for Hammerfall DSP): . The RPM allows for the connection of 2 turntables or 2 line-sources (CD, DVD, sampler etc.) and a microphone to a desktop or laptop computer. A total of 5 independent inputs are routed to 2 stereo outputs plus a separate headphone output, which lets you monitor any of the in- and outputs at any time via TotalMix, RME's unique DSP based mixer. External devices can be connected via MIDI I/O to communicate with any adequate audio software. A Neutrik XLR/phono combo jack on the front panel gives access to a microphone preamp with the same discrete Class-A frontend found in the RME QuadMic. Its level control ranges from 10 to 60 dB to match any application and microphone. 2 low-noise turntable inputs (Cinch/RCA) with integrated RIAA frequency correction for moving magnet cartridges are located on the back panel. A simple mouse click in the settings dialog lets you change the hardware input sensitivity in three steps within a range of 6 dB. Align the output of your turntables with other equipment connected and optimize the input signal fed to the internal A/D converters. To connect CD-players, tape decks, samplers or other line sources, the phono inputs can easily be switched to "line" with another mouse click. A 6 dB pad function can be engaged to prevent overload, and to optimize gain and level balance between different sources. OUTPUTS Two individual stereo line signals can be output at the back panel's Cinch/RCA connectors. The signals present at the MAIN outputs are also available at an additional pair of balanced stereo TRS jacks, with their levels increased by 6 dB. Possible applications would be e.g. simultaneous connection of a tape deck and a professional power amp, a monitor amp and a DI box on stage, and many more. The stereo jack on the front panel can be used as an additional (third) independent stereo output, or as a headphone connector. The RPM comes with a built-in hardware mixer based on RME's TotalMix technology. Its capability to route and mix any of the inputs and outputs provides the RPM with 3 independent stereo submixes. TotalMix offers perfect monitoring and PFL functionality, removing the need for an additional external mixing desk in many cases. All inputs and outputs are internally processed by high quality AD/DA-converters operating at 110 dB signal/noise ratio. The extremely low jitter on the internal clock results in a superb 24 bit conversion from 32 up to 96 kHz. STAND ALONE OPERATION RME's exclusive Disconnect mode lets you adjust level, input selection and signal mix via your computer, and simply detach the RPM afterwards. If you do not need to record or playback audio with your computer the RPM still serves as a preset mixing preamp, a microphone preamp, headphone mixer or line-splitter with balanced signal output - whatever you need. BYPASS In case of power failure or with your computer disconnected, the phono inputs will be hard-patched to the line outputs. Even in an emergency the unit will still serve as a phono preamp and prevent a complete audio dropout APPLICATIONS Phono/CD/Mic interface. The computer only supplies the user interface and the level meters of the mixer (TotalMix). As above, with sound files playing at the same time. As above, recording the complete session to the computer. All audio is supplied by the computer. The RPM serves as mic preamp, line output and headphone amplifier. The turntables do not play audio but time code to remote control dedicated DJ-software (DigiScratch, PCDJ Scratch etc.) Scratch control via MIDI input (external MIDI controller). The MIDI output controls an external sample player (Groovebox etc.) via MIDI time code. The analog output of the player can be mixed with any other signal using the line input of the RPM and TotalMix.
Music | Computer Hardware | Consumer Electronics | Computer Software
Privacy Policy: www.musical-instruments-uk.org.uk does not collect or store any user information. |
